LED Disco Light in a Jar!
LED Disco Light in a Jar!
LED Disco Light in a Jar!
This one of my entries for the Let It Glow! Contest.

Here is a nice, simple instructable for anyone just starting out with LEDs, soldering and electronics. It uses basic parts, with no mucking about with microcontrollers or timers (as fun as those are!) You can build one in an evening if you have all the parts ready to go.

But what is it? The LED Disco Light in a Jar is exactly what the name implies. Over a dozen RGB LEDs in a mason jar, frantically changing colour in a completely random pattern. It's a neat light effect for your next party, or you can use it to entertain a baby for quite a while!

See the last page for videos.

Step 1: Parts

Here is what you need to build the LED Disco Light in a Jar:1 mason jar, jam jar or anything with a suitably wide neck and a metal cap1 switch1 4xAA battery holder, in a 2x2 configuration1 9V battery snap (mates with the battery holder)24 RGB fast or slow-change LEDs*12 10 ohm resistorssome solid 22 gauge wiresome heatshrinkperfboard or make your own printed circuit board**some 25mm aluminum standoffs and matching screwsGlass Frosting Spray (optional)
  • These LEDs have only two pins, and when power is applied they automatically cycle between red, green, blue, and combinations thereof. You can find them on eBay from various sellers in Hong Kong and elsewhere.
  • ** Making your own PC board isn't tricky, and if you know how to make them I recommend it compared to a perfboard. However, explaining how to make one diverges too far from this Instructable.

    Step 2: Tools

    You will need these tools to build the LED Disco Jar:

    Soldering iron and solder

    Heat gun or carefully controlled lighter

    side cutters

    "helping hands" clamp (optional, but makes things much easier!)

    small needle-nose pliers

    wire strippers

    drill

    hot glue gun

    something to cut perfboard or PC board

    a sharp knife

    PC board manufacturing kit (only if you're making a PC board)

    Step 3: Make the LED Branches

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    My LED Disco Light used 24 RGB LEDs. Yours may use more or less, depending on the size of the jar you've got. The 24 LEDs are arranged in 12 branches, each comprised of a single current-limiting resistor and two LEDs, all connected in series. Each LED receives about 3V, as dictated by the LED's datasheet. Don't exceed this value!

    Those 12 branches are then connected in parallel with each other, so that each branch receives about 6V (3V + 3V + a nominal amount across the resistor).

    You may want to start by "frosting" each LED using a piece of 800-grit sandpaper to diffuse the light a bit.


    I spaced the LEDs in each branch at a random distance, so that when they were place in the jar they would appear randomly placed. Try to make a wide range of branches, but also make sure they will fit inside the jar!


    The assembly is relatively straightforward. Start with the resistor, twisting a bit of wire around one lead and soldering it down. This is where the "helping hands" clamp comes in handy; the pieces tend to move around! Then solder an LED to the other end of that wire. Solder another wire, then the second LED. Finally, solder on the last wire so that it reaches all the way back to the resistor.

    To anyone who has played with LEDs this will seem obvious, but to beginners remember this: OBSERVE POLARITY! LEDs will only light if connected in the right direction, and while nothing will blow up if you hook them up backwards they certainly won't light and you'll be sad. The LEDs have a longer lead (positive) and a shorter lead(negative); when I made my Disco Light I made sure that the long lead was towards the resistor on every branch.

    Step 4: Finish the Branches

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    You should now have a number of branches (in my case, 12). On each one, place a short piece of heat shrink over the resistor. This helps keeps the wires together and makes testing and assembly easier. Shrink the heat shrink with a heat gun or a lighter. If you use a lighter, be careful not to scorch anything!

    Step 5: Test the branches!

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    Before you proceed, it's a good idea to test each branch to make sure it works! The easiest way is using a breadboard and a power supply, but you can hook up each branch to the batteries individually instead.

    Step 6: Make the circuit board

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    If you're lucky enough to have a PC board etching setup, this part will be easy.

    Instructions if you are using a PC Board:

    1. Cut out a piece of copper-clad board that will fit inside the neck of the jar.

    2. Using an etch-resist pen (or in my case, a bottle of nail polish my wife didn't want anymore) draw two concentric circles around the outside edge of the PC board. Make sure there is enough room in the center to mount the battery holder!

    3. Etch the board

    4. Drill 1/32" holes in the tracks at regular intervals around the board, one pair of holes for each branch, and an additional set of holes for the battery/switch.

    5. Drill three more holes approximately as shown, for mounting the standoffs and to pass a wire through the board.

    Instructions if you are using perfboard:

    1. Cut a piece of perfboard that will fit inside the neck of the jar.

    2. Drill three holes in the board in approximately the same place as on the PC board.

    Step 7: Build the lid

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    You should drill the holes in the lid now, so you can use the PC board as a template. Place the PC board on the lid and trace through the holes you drilled. It's easy in my case, since the lid comes apart as two pieces on a mason jar. Drill the holes the same diameter as the ones on the PC board.

    Next cut a hole for the switch. I used a rectangular switch so I had to (very carefully) cut the hole for it using a sharp knife. If your switch is round, you can just drill a hole.

    You may also mount the switch and attach the standoffs at this point. To prevent the switch from moving I glued it in with hot glue.

    The standoffs attach the PC board to the lid, and provide spacing for the switch. The length of the standoffs was chosen to match the height of the switch. In this case, 25mm standoffs were chosen to give enough clearance for the switch, which extended about 22mm below the lid.

    Step 8: Solder the branches onto the PC board

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    Here's the fun/tricky part. Solder each branch onto the PC board, again observing polarity. You may want to mark each circle as the "positive" and "negative" rail beforehand, so you don't end up soldering a branch in reverse. Try to alternate the branches so you don't have any LED directly beside another.

    If you're using perfboard, glue the branches in place first, then solder the "rails" in two circles around the board to connect the branches.

    Once all the branches are soldered in, you can hot glue the battery holder in the middle. Make sure it doesn't cover any of the drilled holes.

    Step 9: Wire up the switch

    LED Disco Light in a Jar!
    Almost done! Now we're going to wire up the switch. Take the 9V battery snap (or if your battery holder has leads instead of snaps, the leads from the battery holder) and solder the black one to the negative rail on the PC board.

    Pass the red one through the large hole drilled in the PC board and up to one terminal on the switch. Solder in on - it doesn't matter which terminal it gets soldered to. Grab a piece of wire and solder it to the other terminal on the switch. Pass it through the hole and solder it onto the positive rail of the PC board.

    Load up some batteries, and switch it on! It should light up now.

    Once you know that everything works, you can attach the lid to the PC board. Line up the standoffs and insert screws from the other side of the PC board. Everything should hold together tight.

    Step 10: Final Assembly

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    Now just drop the completed light array into the jar, and tighten the lid. Go ahead, turn it on and make sure it's still working!

    Oooooh, shiny!

    If you like seeing the LEDs through the glass, then consider this project done. However, if you've prefer a bit of mystery, you can frost the glass using glass frosting spray or glass etching cream. I used Rustoleum glass frosting spray. Frosting the inside of the jar hides the mechanics of the Disco Light, and helps diffuse the light a bit.

    Spraying the inside of the jar is messy. Protect the outside using masking tape, and spray a coat inside the jar every few minutes as per the directions on the can. You'll probably find that the frosting spray isn't drying very quickly - I used a heat gun to dry the frosting inside in no time. It will take a few coats to hide the innards. Using white wires and painting the battery holder white will further obscure the contents of the jar.

    Step 11: Videos!

    LED Disco Light in a Jar!
    LED Disco Light in a Jar!
    You're done! This light costs less than $10 to make, even if you buy all the parts new. It's great for jazzing up a party, giving as a gift, or entertaining babies (as you can see in the pictures below!)



    Supplier list:

    LEDs: eBay, seller was 'topbright88'

    Other parts: Sayal electronics (an electronics components store in southern Ontario)

    Small mason jar: Free from my mother in law (thanks!)
    LED Disco Light in a Jar!
    LED_Disco_light.AVI10 MB
    LED Disco Light in a Jar!
    LED_Disco_Dark.AVI14 MB
     
     

    Tag cloud

    make build easy simple arduino making homemade solar laser printed portable cheap mini building custom cardboard wooden create super lego turn paracord chocolate your paper light intel